{"id":301,"date":"2016-04-23T18:11:29","date_gmt":"2016-04-23T22:11:29","guid":{"rendered":"https:\/\/ithinkvirtual.com\/?p=301"},"modified":"2018-02-10T11:21:21","modified_gmt":"2018-02-10T16:21:21","slug":"home-lab-2016-part-3","status":"publish","type":"post","link":"https:\/\/ithinkvirtual.com\/2016\/04\/23\/home-lab-2016-part-3\/","title":{"rendered":"Home Lab 2016 – Part 3"},"content":{"rendered":"
Home Lab 2016 – Part 3<\/strong><\/p>\r\n \u00a0<\/p>\r\n Hello all! \u00a0My sincere apologies for the brief hiatus, but I am back to continue my Home Lab 2016 series. \u00a0In my previous posts, I covered the components that make up my new Home Lab. \u00a0In this post I will quickly cover my Storage and Network solutions that connect my lab. \u00a0Let’s get to it!<\/p>\r\n I will begin by covering my networking components used in my home LAN and LAB. \u00a0<\/p>\r\n <\/p>\r\n My WAN connects to my ISP modem, which then connects to my amazing Ubiquiti EdgeRouter Lite (ERLite-3) via eth0<\/strong>. \u00a0My hardwired LAN connects from eth1<\/strong>\u00a0on the ERLite-3 to port 1 on the SG300-10 (core1).\u00a0\u00a0 Lastly,\u00a0I changed my ASUS router to Access Point mode and connected my Wifi LAN from port 1 of the ASUS to eth2<\/strong>\u00a0on my ERLite-3.<\/p>\r\n <\/a><\/p>\r\n EdgeRouter Connections:<\/p>\r\n <\/a><\/a><\/p>\r\n On to the Cisco SG300-10 (core1), 10-port managed switch, this is configured in Layer 3 (L3) mode and is where I created all of my VLANs and DHCP scopes, etc….<\/p>\r\n <\/a><\/p>\r\n <\/p>\r\n I created the following VLANs on core 1 and allowed them to traverse the trunk to core 2. \u00a0<\/p>\r\n The Cisco SG300-52 is configured in its default Layer 2 (L2) mode and I set up the proper settings, trunk ports, and access ports for each VLAN. \u00a0I understand that I could’ve also configured this in L3-mode and reduce the extra hop to core 1, but I didn’t feel the need to do so for my use case. I may change my mind at some point, but it works for me…for now. \u00a0<\/p>\r\n Due to the way the ethernet cables connected from the switch to each ESXi host, I started configuring\u00a0the switch ports at the end of the switch and worked my way towards to the beginning of the switch ports.<\/p>\r\n <\/a><\/p>\r\n <\/p>\r\n <\/a><\/p>\r\n <\/p>\r\n Next, let’s take a look at Shared Storage. \u00a0I run my shared storage infrastructure on Synology DiskStation hardware, because…they’re flat out awesome, and give you a ton of bang for your buck!<\/p>\r\n I have to say I absolutely love the Synology products, and my DS415+ rocks! \u00a0I have this running 4 SSD’s and a DX213 expansion unit attached with 2 HDD’s in in. \u00a0It runs DSM 6.0-* update *. The interface is slick and setting up the device is a breeze. \u00a0I am currently using NFS only in my lab, and plan to incorporate VSAN soon, as well as testing out iSCSI vs NFS performance. \u00a0For my disk setup, I decided to use the Micron 500DC SSD drives as\u00a0my first Disk Group (Disk Group 1) for my performance volume (Volume 1), the Micron 510DC drives for SSD Cache, and the HGST drives as my 2nd Disk Group (Disk Group 2) for all other storage volumes (Volume 2-x; ISOs, Backups, etc.)<\/p>\r\n <\/a><\/a><\/p>\r\n Well, there you have it. \u00a0In my next posts, I will go over the basic setup and configurations of my Home Lab. \u00a0<\/p>\r\n I hope you enjoyed the read! \u00a0<\/p>\r\n Don’t forget to comment and subscribe!<\/p>\r\n\t
\r\n\t
\r\n\t
\r\n\t
\r\n\t
\r\n\t